#define INTEL_QUARK_SDIO_PCI_DID        0x08A7  /* Intel Quark SDIO PCI Device ID       */
#define INTEL_QUARK_SDIO_PCI_VID        0x8086  /* Intel Quark SDIO MAC PCI Vendor ID   */

#ifndef Nsdmc
#define Nsdmc           1               /* Number of SD Memory Cards            */
#endif

struct sdmcblk {
        sid32   cmd_sem;                /* Command semaphore                    */
        sid32   tx_sem;                 /* Transfer semaphore                   */
        uint32  rca;                    /* Relative card address                */
        char    cid[16];                /* Card identifier                      */
        uint8   cmd8    :1;             /* Card supports CMD8                   */
        uint8   sdio    :1;             /* Card is an SDIO card                 */
        uint8   rsvd    :6;
};
extern  struct  sdmcblk sdmctab[];

#pragma pack(1)
struct sdmc_csreg {
        uint32  sys_adr;                /* Sdma system address register         */
        uint16  blk_size;               /* Block size register                  */
        uint16  blk_count;              /* Block count register                 */
        uint32  argument;               /* Argument register                    */
        uint16  tx_mode;                /* Transfer mode register               */
        uint16  cmd;                    /* Command register                     */
        uint32  response0;              /* Response register 0                  */
        uint32  response2;              /* Response register 2                  */
        uint32  response4;              /* Response register 4                  */
        uint32  response6;              /* Response register 6                  */
        uint32  buf_data_port;          /* Buffer data port register            */
        uint32  pre_state;              /* Present state register               */
        uint8   host_ctl;               /* Host control register                */
        uint8   pwr_ctl;                /* Power control register               */
        uint8   blk_gap_ctl;            /* Block gap control register           */
        uint8   wakeup_ctl;             /* Wakeup control register              */
        uint16  clk_ctl;                /* Clock control register               */
        uint8   timeout_ctl;            /* Timeout control register             */
        uint8   sw_rst;                 /* Software reset register              */
        uint16  nml_int_status;         /* Normal interrupt status register     */
        uint16  err_int_status;         /* Error interrupt status register      */
        uint16  nrm_int_status_en;      /* Normal interrupt status enable       */
        uint16  err_int_stat_en;        /* Error interrupt status enable register */
        uint16  nrm_int_sig_en;         /* Normal interrupt signal enable register */
        uint16  err_int_sig_en;         /* Error interrupt signal enable register */
        uint16  cmd12_err_stat;         /* Auto cmd12 error status register     */
        uint16  host_ctrl_2;            /* Host control 2 register              */
        uint32  capabilities;           /* Capabilities register                */
        uint32  capabilities_2;         /* Capabilities register 2              */
        uint32  max_cur_cap;            /* Maximum current capabilities register*/
        byte    rsvd1[4];
        uint16  force_event_cmd12_err_stat;     /* Force event register for auto cmd12 error status */
        uint16  force_event_err_int_stat;       /* Force event register for error interrupt status */
        uint8   adma_err_stat;          /* Adma error status register           */
        byte    rsvd2[3];
        uint32  adma_sys_addr;          /* Adma system address register */
        byte    rsvd3[4];
        uint16  preset_value_0;         /* Initialization preset values register */
        uint16  preset_value_1;         /* Default speed preset values register */
        uint16  preset_value_2;         /* High speed preset values register */
        uint16  preset_value_3;         /* Sdr12 preset values register */
        uint16  preset_value_4;         /* Sdr25 preset values register */
        uint16  preset_value_5;         /* Sdr50 preset values register */
        uint16  preset_value_6;         /* Sdr104 preset values register */
        uint16  preset_value_7;         /* Ddr50 preset values register */
        uint32  boot_timeout_ctrl;      /* Boot time-out control register */
        uint8   debug_sel;              /* Debug selection register */
        byte    rsvd4[107];
        uint32  shared_bus;             /* Shared bus control register */
        byte    rsvd5[12];
        uint8   spi_int_sup;            /* Spi interrupt support register */
        byte    rsvd6[11];
        uint16  slot_int_stat;          /* Slot interrupt status register */
        uint16  host_ctrl_ver;          /* Host controller version register */
};
#pragma pack()

struct sdmc_cmd {
        uint16  resp_type_sel   :2;
        uint16  cmd_crc_chk_en  :1;
        uint16  cmd_index_chk_en:1;
        uint16  dat_pr_sel      :2;
        uint16  cmd_type        :2;
        uint16  cmd_index       :6;
        uint16  rsvd            :2;
};

struct sdmc_capabilities {
        uint32  timeout_clock_frequency :6;     /* Timeout Clock Frequency              */
        uint32  rsvd6                   :1;     /* RSVD6                                */
        uint32  timeout_clock_unit      :1;     /* Timeout Clock Unit                   */
        uint32  base_clock_frequency_sd_clk:8;  /* Base Clock Frequency for SD Clock    */
        uint32  max_block_length        :2;     /* Max Block Length                     */
        uint32  extended_media_bus_support:1;   /* Extended Media Bus Support           */
        uint32  adma2_support           :1;     /* ADMA2 Support                        */
        uint32  rsvd5                   :1;     /* RSVD5                                */
        uint32  high_speed_support      :1;     /* High Speed Support                   */
        uint32  sdma_support            :1;     /* SDMA Support                         */
        uint32  suspend_resume_support  :1;     /* Suspend / Resume Support             */
        uint32  volt_support_3p3v       :1;     /* Voltage Support 3.3V                 */
        uint32  volt_support_3p0v       :1;     /* Voltage Support 3.0V                 */
        uint32  volt_support_1p8v       :1;     /* Voltage Support 1.8V                 */
        uint32  rsvd4                   :1;     /* RSVD4                                */
        uint32  sys_bus_support_64b     :1;     /* 64-bit System Bus Support            */
        uint32  async_int_support       :1;     /* Asynchronous Interrupt Support       */
        uint32  slot_type               :2;     /* Slot Type                            */
};

/* Individual Bits in Control and Status Registers      */

/* Host Control Register */
#define SDMC_HOST_CTL_LED_CTL           0x0001  /* LED Control  */
#define SDMC_HOST_DAT_TX_4BIT           0x0002  /* Set 4 Bit Bus Width  */
#define SDMC_HOST_HS_EN                         0x0004  /* High Speed Enable    */
#define SDMC_HOST_ADMA_32                       0x0010  /* 32 bit ADMA                  */
#define SDMC_HOST_ADMA_64                       0x0018  /* 64 bit ADMA                  */
#define SDMC_HOST_CARD_DET_TST          0x0040  /* Card is inserted (test)              */
#define SDMC_HOST_CARD_DET_SIG          0x0080  /* Test signal: card inserted   */

/* Normal Interrupt Status Enable */
#define SDMC_CMD_COMP_STAT_EN           0x0001  /* Command Complete Status Enable       */
#define SDMC_TX_COMP_STAT_EN            0x0002  /* Transfer Complete Status Enable      */
#define SDMC_BLK_GAP_EVENT_STAT_EN      0x0004  /* Block Gap Event Status Enable        */
#define SDMC_DMA_INT_STAT_EN            0x0008  /* DMA Interrupt Status Enable          */
#define SDMC_BUF_WR_RDY_STAT_EN         0x0010  /* Buffer Write Ready Status Enable     */
#define SDMC_BUF_RD_RDY_STAT_EN         0x0020  /* Buffer Read Ready Status Enable      */
#define SDMC_CRD_INS_STAT_EN            0x0040  /* Card Insertion Status Enable         */
#define SDMC_CRD_RMV_STAT_EN            0x0080  /* Card Removal Status Enable           */
#define SDMC_CRD_INT_STAT_EN            0x0100  /* Card Interrupt Status Enable         */
#define SDMC_INT_A_STAT_EN              0x0200  /* INT_A Status Enable                  */
#define SDMC_INT_B_STAT_EN              0x0400  /* INT_A Status Enable                  */
#define SDMC_INT_C_STAT_EN              0x0800  /* INT_A Status Enable                  */
#define SDMC_RE_TUNE_STAT_EN            0x1000  /* Re-Tuning Event Status Enable        */
#define SDMC_NML_INT_ALL_STAT_EN        0x1FFF  /* Enable all interrupt status          */

/* Normal Interrupt Signal Enable */
#define SDMC_CMD_COMP_SIG_EN            0x0001  /* Command Complete Signal Enable       */
#define SDMC_TX_COMP_SIG_EN             0x0002  /* Transfer Complete Signal Enable      */
#define SDMC_BLK_GAP_EVENT_SIG_EN       0x0004  /* Block Gap Event Signal Enable        */
#define SDMC_DMA_INT_SIG_EN             0x0008  /* DMA Interrupt Signal Enable          */
#define SDMC_BUF_WR_RDY_SIG_EN          0x0010  /* Buffer Write Ready Signal Enable     */
#define SDMC_BUF_RD_RDY_SIG_EN          0x0020  /* Buffer Read Ready Signal Enable      */
#define SDMC_CRD_INS_SIG_EN             0x0040  /* Card Insertion Signal Enable         */
#define SDMC_CRD_RMV_SIG_EN             0x0080  /* Card Removal Signal Enable           */
#define SDMC_CRD_INT_SIG_EN             0x0100  /* Card Interrupt Signal Enable         */
#define SDMC_INT_A_SIG_EN               0x0200  /* INT_A Signal Enable                  */
#define SDMC_INT_B_SIG_EN               0x0400  /* INT_A Signal Enable                  */
#define SDMC_INT_C_SIG_EN               0x0800  /* INT_A Signal Enable                  */
#define SDMC_RE_TUNE_SIG_EN             0x1000  /* Re-Tuning Event Signal Enable        */
#define SDMC_NML_INT_ALL_SIG_EN 0x1FFF  /* Enable all interrupt signals         */

/* Normal Interrupt Status Register */
#define SDMC_NML_INT_CMD_COMP           0x0001  /* Command Complete                     */
#define SDMC_NML_INT_TX_COMP            0x0002  /* Transfer Complete                    */
#define SDMC_NML_INT_BLK_GAP_EVENT      0x0004  /* Block Gap Event                      */
#define SDMC_NML_INT_DMA_INT            0x0008  /* DMA Interrupt                        */
#define SDMC_NML_INT_BUF_WR_RDY         0x0010  /* Buffer Write Ready                   */
#define SDMC_NML_INT_BUF_RD_RDY         0x0020  /* Buffer Read Ready                    */
#define SDMC_NML_INT_CRD_INS            0x0040  /* Card Insertion                       */
#define SDMC_NML_INT_CRD_RM             0x0080  /* Card Removal                         */
#define SDMC_NML_INT_CRD_INT            0x0100  /* Card Interrupt                       */
#define SDMC_NML_INT_INT_A              0x0200  /* INT_A                                */
#define SDMC_NML_INT_INT_B              0x0400  /* INT_B                                */
#define SDMC_NML_INT_INT_C              0x0800  /* INT_C                                */
#define SDMC_NML_INT_RE_TUNE            0x1000  /* Re-Tuning Event                      */
#define SDMC_NML_INT_BOOT_CK_RCV        0x2000  /* Boot Acknowledge Received            */
#define SDMC_NML_INT_BOOT_TER_INT       0x4000  /* Boot Terminate Interrupt             */
#define SDMC_NML_INT_ERR_INT            0x8000  /* Error Interrupt                      */

/* Error Interrupt Status Enable */
#define SDMC_ERR_INT_CMD_TIMEOUT_ERR_STAT_EN    0x0001  /* Command Timeout Error Status Enable  */
#define SDMC_ERR_INT_CMD_CRC_ERR_STAT_EN        0x0002  /* Command CRC Error Status Enable      */
#define SDMC_ERR_INT_CMD_END_BIT_ERR_STAT_EN    0x0004  /* Command End Bit Error Status Enable  */
#define SDMC_ERR_INT_CMD_IND_ERR_STAT_EN        0x0008  /* Command Index Error Status Enable    */
#define SDMC_ERR_INT_DATA_TIMEOUT_ERR_STAT_EN   0x0010  /* Data Timeout Error Status Enable     */
#define SDMC_ERR_INT_DATA_CRC_ERR_STAT_EN       0x0020  /* Data CRC Error Status Enable         */
#define SDMC_ERR_INT_DATA_END_BIT_ERR_STAT_EN   0x0040  /* Data End Bit Error Status Enable     */
#define SDMC_ERR_INT_CUR_LIMIT_ERR_STAT_EN      0x0080  /* Current Limit Error Status Enable    */
#define SDMC_ERR_INT_CMD12_ERR_STAT_EN          0x0100  /* Auto CMD12 Error Status Enable       */
#define SDMC_ERR_INT_ADMA_ERR_STAT_EN           0x0200  /* ADMA Error Status Enable             */
#define SDMC_ERR_INT_TUNE_ERR_STAT_EN           0x0400  /* Tuning Error Status Enable           */
#define SDMC_ERR_INT_TGT_RSP_ERR_EN             0x1000  /* Target Response Error Status Enable  */
#define SDMC_ERR_INT_CEATA_ERR_EN               0x2000  /* CEATA Error Status Enable            */
#define SDMC_ERR_INT_ALL_STAT_EN                0x3FFF  /* Enable all interrupt signals         */

/* Error Interrupt Signal Enable */
#define SDMC_ERR_INT_CMD_TIMEOUT_ERR_SIG_EN     0x0001  /* Command Timeout Error Signal Enable  */
#define SDMC_ERR_INT_CMD_CRC_ERR_SIG_EN         0x0002  /* Command CRC Error Signal Enable      */
#define SDMC_ERR_INT_CMD_END_BIT_ERR_SIG_EN     0x0004  /* Command End Bit Error Signal Enable  */
#define SDMC_ERR_INT_CMD_IND_ERR_SIG_EN         0x0008  /* Command Index Error Signal Enable    */
#define SDMC_ERR_INT_DATA_TIMEOUT_ERR_SIG_EN    0x0010  /* Data Timeout Error Signal Enable     */
#define SDMC_ERR_INT_DATA_CRC_ERR_SIG_EN        0x0020  /* Data CRC Error Signal Enable         */
#define SDMC_ERR_INT_DATA_END_BIT_ERR_SIG_EN    0x0040  /* Data End Bit Error Signal Enable     */
#define SDMC_ERR_INT_CUR_LIMIT_ERR_SIG_EN       0x0080  /* Current Limit Error Signal Enable    */
#define SDMC_ERR_INT_CMD12_ERR_SIG_EN           0x0100  /* Auto CMD12 Error Signal Enable       */
#define SDMC_ERR_INT_ADMA_ERR_SIG_EN            0x0200  /* ADMA Error Signal Enable             */
#define SDMC_ERR_INT_TUNE_ERR_SIG_EN            0x0400  /* Tuning Error Signal Enable           */
#define SDMC_ERR_INT_TGT_RSP_ERR_SIG_EN         0x1000  /* Target Response Error Signal Enable  */
#define SDMC_ERR_INT_CEATA_ERR_SIG_EN           0x2000  /* CEATA Error Signal Enable            */
#define SDMC_ERR_INT_ALL_SIG_EN                         0x3FFF  /* Enable all interrupt signals         */

/* Error Interrupt Status Register */
#define SDMC_ERR_INT_CMD_TIMEOUT_ERR            0x0001  /* Command Timeout Error                */
#define SDMC_ERR_INT_CMD_CRC_ERR                0x0002  /* Command CRC Error                    */
#define SDMC_ERR_INT_CMD_END_BIT_ERR            0x0004  /* Command End Bit Error                */
#define SDMC_ERR_INT_CMD_INDEX_ERR              0x0008  /* Command Index Error                  */
#define SDMC_ERR_INT_DATA_TIMEOUT_ERR           0x0010  /* Data Timeout Error                   */
#define SDMC_ERR_INT_DATA_CRC_ERR               0x0020  /* Data CRC Error                       */
#define SDMC_ERR_INT_DATA_END_BIT_ERR           0x0040  /* Data End Bit Error                   */
#define SDMC_ERR_INT_CUR_LIMIT_ERR              0x0080  /* Current Limit Error                  */
#define SDMC_ERR_INT_CMD12_ERR                  0x0100  /* Auto CMD Error                       */
#define SDMC_ERR_INT_ADMA_ERR                   0x0200  /* ADMA Error                           */
#define SDMC_ERR_INT_TUNE_ERR                   0x0400  /* Tuning Error                         */
#define SDMC_ERR_INT_TGT_RSP_ERR                0x1000  /* Target Response Error                */
#define SDMC_ERR_INT_CEATA_ERR                  0x2000  /* CEATA Error                          */

/* Software Reset Register */
#define SDMC_SW_RST_ALL                 0x01    /* Software Reset For All               */
#define SDMC_SW_RST_CMD_LN              0x02    /* Software Reset For CMD Line          */
#define SDMC_SW_RST_DAT_LN              0x04    /* Software Reset for DAT Line          */

/* Capabilities Register */
#define SDMC_CAP_VOLT_SUPPORT_3P3V      0x01000000      /* Voltage Support 3.3V         */
#define SDMC_CAP_VOLT_SUPPORT_3P0V      0x02000000      /* Voltage Support 3.0V         */
#define SDMC_CAP_VOLT_SUPPORT_1P8V      0x04000000      /* Voltage Support 1.8V         */

/* Present State Status Register */
#define SDMC_PRE_STATE_CMD_INHIBIT_CMD  0x00000001      /* Command Inhibit              */
#define SDMC_PRE_STATE_CMD_INHIBIT_DAT  0x00000002      /* Command Inhibit DAT          */
#define SDMC_PRE_STATE_CRD_INS          0x00010000      /* Card Inserted                */
#define SDMC_PRE_STATE_DATA_LN_SIG_LVL  0x00F00000      /* Line Signal Level            */

/* Clock Control Register */
#define SDMC_CLK_CTL_INT_CLK_EN         0x0001  /* Internal Clock Enable                */
#define SDMC_CLK_CTL_INT_CLK_STABLE     0x0002  /* Internal Clock Stable                */
#define SDMC_CLK_CTL_SD_CLK_EN          0x0004  /* SD Clock Enable                      */
#define SDMC_CLK_CTL_CLK_GEN_SEL        0x0020  /* Clock Generator Select               */
#define SDMC_CLK_CTL_SD_FREQ_HIGH_MASK  0x00FF  /* Mask to set SD clock frequency to max*/

/* Timeout Control Register */
#define SDMC_TMR_CTL_HIGH               0x0E    /* Mask to set timeout to max   */

/* Power Control Register */
#define SDMC_PWR_CTL_SD_BUS_PWR                 0x01    /* SD Bus Power                 */
#define SDMC_PWR_CTL_HW_RST                     0x10    /* HW Reset                     */
#define SDMC_PWR_CTL_SD_BUS_VOL_SEL_CLR         0xF1    /* Clear mask for SD bus voltage*/
#define SDMC_PWR_CTL_SD_BUS_VOL_SEL_3P3V        0x0E    /* Set mask for 3.3V            */
#define SDMC_PWR_CTL_SD_BUS_VOL_SEL_3P0V        0x0C    /* Set mask for 3.0V            */
#define SDMC_PWR_CTL_SD_BUS_VOL_SEL_1P8V        0x0A    /* Set mask for 1.8V            */

/* Transfer Mode Register */
#define SDMC_TXM_DMA_EN                 0x0001          /* DMA Enable           */
#define SDMC_TXM_BLK_CNT_EN             0x0002          /* Block Count Enable           */
#define SDMC_TXM_AUTO_CMD12_EN  0x0004          /* Auto CMD12 Enable            */
#define SDMC_TXM_DAT_TX_RD              0x0010          /* Data Direction Read          */
#define SDMC_TXM_MB_SEL                 0x0020          /* Multi block select           */

/* Card Status Response (R1) */
#define SDMC_R1_AKE_SEQ_ERROR           0x00000008      /* Authentication Error         */
#define SDMC_R1_APP_CMD                 0x00000020      /* Next command is application  */
#define SDMC_R1_READY_FOR_DATA          0x00000100      /* Card ready for data          */
#define SDMC_R1_CURRENT_STATE           0x00001E00      /* Current card state           */
#define SDMC_R1_ERASE_RESET             0x00002000      /* Erase processes reset        */
#define SDMC_R1_CARD_ECC_DISABLED       0x00004000      /* Command without ECC          */
#define SDMC_R1_WP_ERASE_SKIP           0x00008000      /* Write protected              */
#define SDMC_R1_CSD_OVERWRITE           0x00010000      /* Error in CSD overwrite       */
#define SDMC_R1_ERROR                   0x00080000      /* Unknown error                */
#define SDMC_R1_CC_ERROR                0x00100000      /* Internal controller error    */
#define SDMC_R1_CARD_ECC_FAILED         0x00200000      /* ECC correction failed        */
#define SDMC_R1_ILLEGAL_COMMAND         0x00400000      /* Not a legal command          */
#define SDMC_R1_COM_CRC_ERROR           0x00800000      /* Previous command CRC failed  */
#define SDMC_R1_LOCK_UNLOCK_FAILED      0x01000000      /* Lock/unlock of card failed   */
#define SDMC_R1_CARD_IS_LOCKED          0x02000000      /* Card is locked               */
#define SDMC_R1_WP_VIOLATION            0x04000000      /* Write to protected block     */
#define SDMC_R1_ERASE_PARAM             0x08000000      /* Invalid erase parameter      */
#define SDMC_R1_ERASE_SEQ_ERROR         0x10000000      /* Invalid erase sequence       */
#define SDMC_R1_BLOCK_LEN_ERROR         0x20000000      /* TX block length not allowed  */
#define SDMC_R1_ADDRESS_ERROR           0x40000000      /* Misaligned address           */
#define SDMC_R1_OUT_OF_RANGE            0x80000000      /* Argument out of range        */
#define SDMC_R1_ANY_ERROR                       0xFDF90008  /* Combined mask for any error */

/* Card state */
#define SDMC_R1_IDLE_STATE              0x00000000      /* Idle State                   */
#define SDMC_R1_READY_STATE             0x00000200      /* Ready State                  */
#define SDMC_R1_IDENT_STATE             0x00000400      /* Identification State         */
#define SMDC_R1_STBY_STATE              0x00000600      /* Standby State                */
#define SDMC_R1_TRAN_STATE              0x00000800      /* Transfer State               */
#define SDMC_R1_DATA_STATE              0x00000A00      /* Sending-data State           */
#define SDMC_R1_RCV_STATE               0x00000C00      /* Receive-data State           */
#define SDMC_R1_PRG_STATE               0x00000E00      /* Programming State            */
#define SMDC_R1_DIS_STATE               0x00001000      /* Disconnect State             */

/* Operating Conditions Register Response (R3) */
#define SDMC_R3_2P7_2P8                 0x00008000      /* Voltage Range 2.7V - 2.8V    */
#define SDMC_R3_2P8_2P9                 0x00010000      /* Voltage Range 2.8V - 2.9V    */
#define SDMC_R3_2P9_3P0                 0x00020000      /* Voltage Range 2.9V - 3.0V    */
#define SDMC_R3_3P0_3P1                 0x00040000      /* Voltage Range 3.0V - 3.1V    */
#define SDMC_R3_3P1_3P2                 0x00080000      /* Voltage Range 3.1V - 3.2V    */
#define SDMC_R3_3P2_3P3                 0x00100000      /* Voltage Range 3.2V - 3.3V    */
#define SDMC_R3_3P3_3P4                 0x00200000      /* Voltage Range 3.3V - 3.4V    */
#define SDMC_R3_3P4_3P5                 0x00400000      /* Voltage Range 3.4V - 3.5V    */
#define SDMC_R3_3P5_3P6                 0x00800000      /* Voltage Range 3.5V - 3.6V    */
#define SDMC_R3_S18A                    0x01000000      /* Switching to 1.8V accepted   */
#define SDMC_R3_UHS_II_STS              0x20000000      /* UHS-II card status           */
#define SDMC_R3_CCS                     0x40000000      /* Card capacity status         */
#define SDMC_R3_BUSY                    0x80000000      /* Card power up status (busy)  */

/* Published RCA Response (R6) */
#define SDMC_R6_RCA_MASK                0xFFFF0000      /* Relative card address mask   */
#define SDMC_R6_AKE_SEQ_ERROR           0x00000008      /* Authentication Error         */
#define SDMC_R6_APP_CMD                 0x00000020      /* Next command is application  */
#define SDMC_R6_READY_FOR_DATA          0x00000100      /* Card ready for data          */
#define SDMC_R6_CURRENT_STATE           0x00001E00      /* Current card state           */
#define SDMC_R6_ERROR                   0x00002000      /* Unknown error                */
#define SDMC_R6_ILLEGAL_COMMAND         0x00004000      /* Not a legal command          */
#define SDMC_R6_COM_CRC_ERROR           0x00008000      /* Previous command CRC failed  */

/* ACMD41 Argument Flags */
#define SDMC_OCR_MASK                   0x00FFFF00      /* OCR set mask                 */
#define SDMC_ACMD41_S18R                0x01000000      /* Switching to 1.8V request    */
#define SDMC_ACMD41_XPC                 0x10000000      /* Extended capacity power ctl  */
#define SDMC_ACMD41_HCS                 0x40000000      /* High capacity card support   */

/* Command Resgitser */
#define SDMC_CMD_TYPE_NML               0x0000          /* Normal Command Type          */
#define SDMC_CMD_TYPE_SUS               0x0040          /* Suspend Command Type         */
#define SDMC_CMD_TYPE_RSM               0x0080          /* Resume Command Type          */
#define SDMC_CMD_TYPE_ABT               0x00C0          /* Abort Command Type           */
#define SDMC_CMD_DAT_PRES               0x0020          /* Data Present Flag            */
#define SDMC_CMD_CMD_IDX_EN             0x0010          /* Index Check Enable Flag      */
#define SDMC_CMD_CMD_CRC_EN             0x0008          /* CRC Check Enable Flag        */
#define SDMC_CMD_CMD_RSP_LG             0x0001          /* 138 Bit Response Length      */
#define SDMC_CMD_CMD_RSP_ST             0x0002          /* 48 Bit Response Length       */
#define SDMC_CMD_CMD_RSP_ST_BSY 0x0003          /* 48 Bit Response Length Check Busy */

/* Expected Command Response Types */
#define SDMC_CMD_NO_RESP        (0x0000)
#define SDMC_CMD_R1                     (SDMC_CMD_CMD_RSP_ST | SDMC_CMD_CMD_IDX_EN | SDMC_CMD_CMD_CRC_EN)
#define SDMC_CMD_R1b            (SDMC_CMD_CMD_RSP_ST_BSY | SDMC_CMD_CMD_IDX_EN | SDMC_CMD_CMD_CRC_EN)
#define SDMC_CMD_R2                     (SDMC_CMD_CMD_RSP_LG | SDMC_CMD_CMD_CRC_EN)
#define SDMC_CMD_R3                     (SDMC_CMD_CMD_RSP_ST)
#define SDMC_CMD_R4                     (SDMC_CMD_CMD_RSP_ST)
#define SDMC_CMD_R5                     (SDMC_CMD_CMD_RSP_ST | SDMC_CMD_CMD_IDX_EN | SDMC_CMD_CMD_CRC_EN)
#define SDMC_CMD_R5b            (SDMC_CMD_CMD_RSP_ST_BSY | SDMC_CMD_CMD_IDX_EN | SDMC_CMD_CMD_CRC_EN)
#define SDMC_CMD_R6                     (SDMC_CMD_CMD_RSP_ST | SDMC_CMD_CMD_IDX_EN | SDMC_CMD_CMD_CRC_EN)
#define SDMC_CMD_R7                     (SDMC_CMD_CMD_RSP_ST | SDMC_CMD_CMD_IDX_EN | SDMC_CMD_CMD_CRC_EN)

/* Command Definitions with Expected Response Types */
#define SDMC_CMD0               0x0000 | (SDMC_CMD_NO_RESP)             /* CMD0 - Go Idle State (Reset)         */
#define SDMC_CMD2               0x0200 | (SDMC_CMD_R2)                  /* CMD2 - All send card identifier      */
#define SDMC_CMD3               0x0300 | (SDMC_CMD_R6)                  /* CMD3 - Send relative card address    */
#define SDMC_CMD7               0x0700 | (SDMC_CMD_R1b)                 /* CMD7 - Select/Deselect card          */
#define SDMC_CMD8               0x0800 | (SDMC_CMD_R7)                  /* CMD8 - Voltage check                 */
#define SDMC_CMD9               0x0900 | (SDMC_CMD_R2)                  /* CMD9 - Send CSD                      */
#define SDMC_CMD10              0x0A00 | (SDMC_CMD_R2)                  /* CMD10 - Send CID                     */
#define SDMC_CMD12              0x0C00 | (SDMC_CMD_R1b)                 /* CMD12 - Stop Transmission            */
#define SDMC_ABT                0x0C00 | (SDMC_CMD_TYPE_ABT)    /* CMD12 - Abort                        */
#define SDMC_CMD13              0x0D00 | (SDMC_CMD_R1)                  /* CMD13 - Send status                  */
#define SDMC_CMD16              0x1000 | (SDMC_CMD_R1)                  /* CMD16 - Set block length             */
#define SDMC_CMD17              0x1100 | (SDMC_CMD_R1 | SDMC_CMD_DAT_PRES)      /* CMD17 - Single block read            */
#define SDMC_CMD55              0x3700 | (SDMC_CMD_R1)                  /* CMD55 - Application specific command */
#define SDMC_ACMD6              0x0600 | (SDMC_CMD_R1)                  /* ACMD6 - Set bus width        */
#define SDMC_ACMD41             0x2900 | (SDMC_CMD_R3)                  /* ACMD41 - Card Initialization/Inquiry */
#define SDMC_ACMD51             0x3300 | (SDMC_CMD_R1 | SDMC_CMD_DAT_PRES )  /* ACMD51 - Send SCR               */

#define SDMC_CMD_DELAY                  100000          /* Delay in micro secs  */

#define SDMC_BLK_SIZE                   512                     /* Block size used for data transfers */

#define SDMC_RC_OK                      (0)
#define SDMC_RC_RECOVERABLE_ERR         (-1)
#define SDMC_RC_NON_RECOVERABLE_ERROR   (-2)

#define SDMC_CMD_NO_FLAGS               0x00    /* No flags used with the command       */
#define SDMC_CMD_NO_ERR_RCVY            0x01    /* Do not perform error recovery        */
#define SDMC_CMD_DAT_TRNS               0x02    /* Wait for data transmission           */

devcall sdmc_issue_cmd_sync (volatile struct sdmc_csreg *csrptr, uint16 cmd_value, uint32 arg_value, uint16* error_sts, uint8 flags);
devcall sdmc_issue_cmd_async (volatile struct sdmc_csreg *csrptr, uint16 cmd_value, uint32 arg_value);
devcall sdmc_finalize_cmd_async (volatile struct sdmc_csreg *csrptr, uint16* error_sts);