/* uart.h - definintions for the NS16550 uart serial hardware */

#define UART_BAUD       115200  /* Default console baud rate.           */
#define UART_OUT_IDLE   0x0016  /* Determine if transmit idle           */
#define UART_FIFO_SIZE  16      /* Chars in UART onboard output FIFO    */
                                /* (16 for later UART chips)            */
#define INTEL_QUARK_UART_PCI_DID        0x0936  /* UART PCI Device ID   */
#define INTEL_QUARK_UART_PCI_VID        0x8086  /* UART PCI Vendor ID   */
/*
 * Control and Status Register (CSR) definintions for the 16550 UART.
 * The code maps the structure structure directly onto the base address
 * CSR address for the device.
 */
struct  uart_csreg
{
        volatile uint32 buffer; /* Receive buffer (when read)           */
                                /*   OR transmit hold (when written)    */
        volatile uint32 ier;    /* Interrupt enable                     */
        volatile uint32 iir;    /* Interrupt identification (when read) */
                                /*   OR FIFO control (when written)     */
        volatile uint32 lcr;    /* Line control register                */
        volatile uint32 mcr;    /* Modem control register               */
        volatile uint32 lsr;    /* Line status register                 */
        volatile uint32 msr;    /* Modem status register                */
        volatile uint32 scr;    /* Scratch register                     */
};

/* Alternative names for control and status registers */

#define rbr     buffer          /* Receive buffer (when read)           */
#define thr     buffer          /* Transmit hold (when written)         */
#define fcr     iir             /* FIFO control (when written)          */
#define dll     buffer          /* Divisor latch (low byte)             */
#define dlm     ier             /* Divisor latch (high byte)            */

/* Definintion of individual bits in control and status registers       */

/* Port offsets from the base */

#define UART_DLL        0x00    /* Value for low byte of divisor latch  */
                                /*      DLAB=0                          */
#define UART_DLM        0x01    /* Value for high byte of divisor latch */
                                /*      DLAB=1                          */

/* Line control bits */

#define UART_LCR_DLAB   0x80    /* Divisor latch access bit             */
#define UART_LCR_8N1    0x03    /* 8 bits, no parity, 1 stop            */

/* Interrupt enable bits */

#define UART_IER_ERBFI  0x01    /* Received data interrupt mask         */
#define UART_IER_ETBEI  0x02    /* Transmitter buffer empty interrupt   */
#define UART_IER_ELSI   0x04    /* Recv line status interrupt mask      */
#define UART_IER_EMSI   0x08    /* Modem status interrupt mask          */

/* Interrupt identification masks */

#define UART_IIR_IRQ    0x01    /* Interrupt pending bit                */
#define UART_IIR_IDMASK 0x0E    /* 3-bit field for interrupt ID         */
#define UART_IIR_MSC    0x00    /* Modem status change                  */
#define UART_IIR_THRE   0x02    /* Transmitter holding register empty   */
#define UART_IIR_RDA    0x04    /* Receiver data available              */
#define UART_IIR_RLSI   0x06    /* Receiver line status interrupt       */
#define UART_IIR_RTO    0x0C    /* Receiver timed out                   */

/* FIFO control bits */

#define UART_FCR_EFIFO  0x01    /* Enable in and out hardware FIFOs     */
#define UART_FCR_RRESET 0x02    /* Reset receiver FIFO                  */
#define UART_FCR_TRESET 0x04    /* Reset transmit FIFO                  */
#define UART_FCR_TRIG0  0x00    /* RCVR FIFO trigger level one char     */
#define UART_FCR_TRIG1  0x40    /* RCVR FIFO trigger level 1/4          */
#define UART_FCR_TRIG2  0x80    /* RCVR FIFO trigger level 2/4          */
#define UART_FCR_TRIG3  0xC0    /* RCVR FIFO trigger level 3/4          */

/* Modem control bits */

#define UART_MCR_OUT2   0x08    /* User-defined OUT2                    */
#define UART_MCR_RTS    0x02    /* RTS complement                       */
#define UART_MCR_DTR    0x01    /* DTR complement                       */
#define UART_MCR_LOOP   0x10    /* Enable loopback test mode            */

/* Line status bits */

#define UART_LSR_DR     0x01    /* Data ready                           */
#define UART_LSR_BI     0x10    /* Break interrupt indicator            */
#define UART_LSR_THRE   0x20    /* Transmit-hold-register empty         */
#define UART_LSR_TEMT   0x40    /* Transmitter empty                    */